MS20757C
Size code number |
E inch (mm) |
F ±.005 (0.13) inch (mm) |
G ±.005 (0.13) inch (mm) |
H Dia. +.010 (0.25) -.000 inch (mm) |
J Rad. ±.010 (0.25) inch (mm) |
|
8 |
1.390 (35.31) |
± .016 (0.41) |
.250 (6.35) |
.950 (24.13) |
.205 (5.21) |
.219 (5.56) |
10 |
1.468 (37.29) |
1.038 (26.37) |
||||
12 |
1.594 (40.49) |
1.156 (29.36) |
||||
12-16 |
1.750 (44.45) |
1.312 (33.32) |
||||
16 |
||||||
20 |
2.188 (55.58) |
±.020 (0.51) |
1.656 (42.06) |
.266 (6.76) |
.266 (6.76) |
|
20-24 |
2.375 (60.33) |
.312 (7.92) |
1.812 (46.02) |
.281 (7.14) |
||
24 |
||||||
32 |
3.000 (76.20) |
2.375 (60.33) |
.328 (8.33) |
.312 (7.92) |
||
40 |
4.000 (101.60) |
--- |
.375 (9.53) |
|||
48 |
4.500 (114.30) |
--- |
.625 (15.88) |
|||
Size code number |
K Dia. ±.010 (0.25) |
L Dia. |
N Dia. |
T Dia. min |
v min |
8 |
1.782 (45.26) |
1.344 (34.14) |
--- |
--- |
--- |
10 |
1.906 (48.41) |
1.468 (37.29) |
--- |
--- |
--- |
12 |
2.094 (53.19) |
1.635 (41.53) |
.669 (16.99) |
.609 (15.47) |
.065 (1.65) |
12-16 |
2.312 (58.72) |
1.855 (47.12) |
|||
16 |
.904 (22.96) |
.859 (21.82) |
|||
20 |
2.875 (73.03) |
2.342 (59.49) |
1.138 (28.91) |
1.059 (26.90) |
.090 (2.29) |
20-24 |
3.094 (78.59) |
2.562 (65.07) |
|||
24 |
1.372 (34.85) |
1.309 (33.25) |
|||
32 |
3.953 (100.41) |
3.359 (85.32) |
1.841 (46.76) |
1.793 (45.54) |
.100 (2.54) |
40 |
4.500 (114.30) |
3.812 (96.82) |
2.341 (59.46) |
2.243 (56.97) |
|
48 |
5.000 (127.00) |
4.312 (109.52) |
2.841 (72.16) |
2.793 (70.94) |
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified tolerances are ±.005 inch (0.13 mm), angles ±.5°.
4. Break sharp edges .and remove all hanging burrs and slivers
5. Annular tool marks up to 63 µin (1.6 µm) Ra max will be allowed, machined surfaces shall be finished to 100µin (2.54 µm) Ra, unless otherwise specified on the figures. Surface finish shall be in accordance with ASME B46.1.
6. Reduction by forging draft angle of 7° maximum is permissible.
7. Break all sharp edges and remove all hanging burrs or slivers which might become dislodged under usage.
FIGURE 1. Connector fixed flange dimensions and configurations - Continued.
3
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business