MS39210J
Dash Number |
Tube OD |
A Thread |
B Thread Length (mm) |
c (mm) |
D (mm) |
E (mm) |
F (mm) |
G (mm) |
1 |
1/8 |
5/16 24UNF-2B |
.219 (5.56) |
.297 (7.54) |
.130 (3.30) .134(3.40) |
.438 (11.11) |
.275(6.99) .270(6.86) |
.438 (11.11) |
2 |
3/16 |
3/8 24UNF-2B |
.219 (5.56) |
.297 (7.54) |
.190(4.83) .194(4.93) |
.438 (11.11) |
.338(8.59) .333(8.46) |
.500 (12.70) |
3 |
1/4 |
1/2 20UNF-2B |
.281 (7.14) |
.359 (3.13) |
.255(6.48) .259(6.58) |
.563 (14.29) |
.454(11.53) .449(11.40) |
.625 (15.88) |
4 |
5/16 |
9/16 18UNF-2B |
.281 (7.14) |
.390 (3.92) |
.318(8.08) .322(8.18) |
.578 (14.68) |
.512(13.00) .505(12.83) |
.688 (17.46) |
5 |
3/8 |
5/8 18UNF-2B |
.313 (7.94) |
.422 (10.72) |
.380(9.65) .384(9.75) |
.625 (15.88) |
.575(14.61) .568(14.43) |
.750 (19.05) |
6 |
1/2 |
3/4 16UNF-2B |
.328 (3.33) |
.453 (11.51) |
.506(12.85) .510(12.95) |
.688 (17.46) |
.693(17.60) .686(17.42) |
.875 (22.23) |
7 |
5/8 |
15/16 16UN-2B |
.375 (9.53) |
.469 (11.91) |
.633(16.08) .637(16.18) |
.750 (19.05) |
.881(22.38) .874(22.20) |
1.125 (28.58) |
8 |
3/4 |
1-1/16 16UN-2B |
.406 (10.32) |
.500 (12.70) |
.758(19.25) .762(19.35) |
.813 (20.64) |
1.005(25.53) .999(25.37) |
1.250 (31.75) |
9 |
7/8 |
1-3/16 16UN-2B |
.406 (10.32) |
.500 (12.70) |
.883(22.43) .887(22.53) |
.813 (20.64) |
1.131(28.73) 1.124(28.55) |
1.375 (34.93) |
10 |
1 |
1-5/16 16UN-2B |
.406 (10.32) |
.500 (12.70) |
1.008(25.60) 1.012(25.70) |
.813 (20.64) |
1.256(31.90) 1.249(31.72) |
1.500 (38.10) |
11 |
1-1/4 |
1-5/8 16UN-2B |
.406 (10.32) |
.578 (14.68) |
1.206(30.63) 1.264(32.11) |
.844 (31.43) |
1.568(39.83) 1.561(39.65) |
2 (50.80) |
12 |
1-1/2 |
1-7/8 16UN-2B |
.500 (12.70) |
.672 (17.07) |
1.510(38.35) 1.514(38.46) |
.969 (34.61) |
1.818(46.18) 1.810(45.97) |
2.250 (57.15) |
NOTES:
1. Dimensions are in inches, unless otherwise specified. Millimeters are in parentheses.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, the tolerance for 3 place decimals is decimals ± .005, the tolerance for fractions is ± 1/64, the tolerance for degrees is ± 2°.
4. Threads shall be in accordance with FED-STD-H28.
5. Referenced documents shall be of the issue in effect in date of invitations for bid.
6. This illustration is for identification and is not intended to restrict designs or shapes not dimensioned.
FIGURE 1. Nuts, tube coupling - safety sleeve compression type - continued.
2
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business