AN915 Rev 13
A
B
D
E
Pipe size
+.047 (1.19)
C
+.047 (1.19)
+.047 (1.19)
F
Dash
ANPT
-0.000
mm)
-0.000
-0.000
(mm)
number
SAE-AS71051
(mm)
(mm)
(mm)
1
1/8-27
.469 (11.91)
.625 (15.88)
.531 (13.49)
.781 (19.84)
.422 (10.72)
2
1/4-18
.625 (15.88)
.813 (20.65)
.688 (17.48)
1.109 (28.17)
.563 (14.30)
3
3/8-18
.719 (18.26)
.938 (23.83)
.813 (20.65)
1.156 (29.36)
.609 (15.47)
4
1/2-14
.906 (23.01)
1.188 (30.18)
1.016 (25.81)
1.453 (36.91)
.797 (20.24)
1.375 (34.93)
.813 (20.65)
6
3/4-14
.969 (24.61)
1.125 (28.58)
1.531 (38.89)
8
1-11 1/2
1.125 (28.58)
1.750 (44.45)
1.313 (33.35)
1.906 (48.41)
.969 (24.61)
10
1/ 1/4-11 1/2
1.156 (29.36)
2.156 (54.76)
1.438 (36.53)
2.156 (54.76)
.969 (24.61)
M
P
K
S
U
+.047 (1.19)
Dash
Dia.
Dia.
Approx
Approx
-0.000
number
(mm)
(mm)
(mm)
(mm)
(mm)
1
.188 (4.48)
.719 (18.26)
.578 (14.68)
.188 (4.78)
.313 (7.95)
2
.281 (7.14)
1.047 (26.59)
.781 (19.84)
.375 (9.53)
.438 (11.13)
3
.406 (10.31)
1.063 (27.00)
.922 (23.42)
.375 (9.53)
.500 (12.70)
4
.531 (13.49)
1.344 (34.14)
1.156 (29.36)
.500 (12.70)
.625 (15.88)
6
.719 (18.26)
1.375 (34.93)
1.359 (34.52)
.625 (15.88)
.750 (19.05)
8
.938 (23.83)
1.719 (43.66)
1.688 (42.88)
.625 (15.88)
.875 (22.23)
10
1.250 (31.75)
1.875 (47.63)
2.125 (28.58)
.750 (19.05)
1.000 (25.40)
V
W
Dash
Rad.
Rad.
number
(mm)
(mm)
1
.219 (5.56)
.063 (1.60)
2
.281 (7.14)
.094 (2.39)
3
.359 (9.12)
.094 (2.39)
4
.438 (11.13)
.125 (3.18)
6
.547 (13.89)
.125 (3.18)
8
.688 (17.48)
.125 (3.18)
10
.859 (21.82)
.156 (3.96)
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for information only.
3. Unless otherwise specified, tolerances are ±.016 inch (0.41 mm).
4. Break sharp edges and remove all hanging burrs and slivers.
5. Machined surfaces shall be finished to 125µin Ra; forged surfaces shall be 250µin Ra, unless otherwise
specified on the figures. Surface finish shall be in accordance with ASME B46.1.
6. For design features purposes, this standard takes precedence over documents referenced herein.
7. Referenced documents shall be of the issue in effect on date of invitation for bid.
FIGURE 1. Elbow 45° dimensions and configuration - Continued.
REQUIREMENTS:
Dimensions and configuration shall be in accordance with figure 1.
Materials and finishes shall be in accordance with SAE-AS4842; see table I for material code.
2
For Parts Inquires call Parts Hangar, Inc (727) 493-0744
© Copyright 2015 Integrated Publishing, Inc.
A Service Disabled Veteran Owned Small Business